Skip to Content

Applicable Models

This information is for the following models:
  • BDP-S485
  • BDP-S580
  • BDP-S480
  • BDP-S780

About this download

Note: This utility is only for use with the products identified and sold in Asia Pacific. Not all models are sold in all countries.

This utility upgrades BDP-S480/S485/S580/S780 firmware to version M07.R.0600 and provides the following benefits:

  • BRAVIA Internet Video improvement.

What operating systems does this apply to?
Operating System(s):

  • Microsoft® Windows® XP
  • Microsoft® Windows® XP MCE
  • Microsoft® Windows Vista® Home Basic
  • Microsoft® Windows Vista® Home Premium
  • Microsoft® Windows Vista® Business
  • Microsoft® Windows Vista® Ultimate
  • Microsoft® Windows Vista® Home Basic 64-bit
  • Microsoft® Windows Vista® Home Premium 64-bit
  • Microsoft® Windows Vista® Business 64-bit
  • Microsoft® Windows Vista® Ultimate 64-bit
  • Microsoft® Windows ® 7 Home Premium 32-bit
  • Microsoft® Windows ® 7 Home Premium 64-bit
  • Microsoft® Windows ® 7 Professional 32-bit
  • Microsoft® Windows ® 7 Professional 64-bit
  • Microsoft® Windows ® 7 Ultimate 32-bit
  • Microsoft® Windows ® 7 Ultimate 64-bit

Check the Current Firmware Version

  1. Power on the television and make sure it is tuned to the inputs to which the Blu-ray Disc player is connected.
  2. Power on the Blu-ray Disc player.
  3. If the player starts to play a disc, press the "STOP" button and wait until the xross media bar™ menu is displayed on the television before proceeding.
  4. Use the arrow keys on the remote control to select "Setup" – "System Settings", and then press the ENTER button.
  5. Use the arrow keys to select "Quick Start Mode" and make sure that the "Quick Start Mode" is set to "Off".
    If the "Quick Start Mode" is set to "On", change the setting to "Off". Otherwise, the firmware upgrade may not succeed.
  6. Use the arrow keys to select "System Information", and then press the ENTER button.
  7. The firmware version currently installed on the Blu-ray Disc player will be listed on the television screen.

    If the last four digits of the version number are 0600 or higher, it is not necessary to install this firmware upgrade.

Before getting started:

There are two ways to perform the BDP-S480/S485/S580/S780 Firmware upgrade:

  1. Network Upgrade:
    The Network Upgrade operation is straightforward, so it is highly recommended that you use the Network Upgrade method.
    You will need to connect the Blu-ray Disc player to your Internet source using an Ethernet cable.
    Please see the Network Upgrade Instructions section below, for more information.

  2. Create an Upgrade Disc:
    If you cannot connect the Blu-ray Disc player to your Internet source, please use the disc upgrade method.
    Please see the Download the Firmware and Create an Upgrade Disc section, for more information.
    A drive with CD disc burning capability, and a new blank CD-R disc are required to create the upgrade disc.

Network Upgrade procedure

The Network Upgrade operation is straightforward, so it is highly recommended that you use the Network Upgrade method to upgrade the BDP-S480/S485/S580/S780 firmware.

Important:

  • WARNING!! Please follow the upgrade instructions carefully. Failure to follow the instructions may interrupt the upgrade process and may cause the Blu-ray Disc player to be unresponsive or to require repair.
  • WARNING!! Do not power off the Blu-ray Disc player or disconnect it from the AC power outlet. Loss of power during the installation of the firmware upgrade may cause the Blu-ray Disc player to be unresponsive or to require repair.
  • In order to use this upgrade method it is necessary to have the player correctly connected to an active Internet connection.
  • In order to perform the firmware upgrade, it is necessary to have the player correctly connected to a compatible television.

The firmware update process usually takes about 15 to 30 minutes, depending on system configuration and network connection. 

  1. Power on the television and make sure it is tuned to the inputs to which the BD player is connected.
  2. Connect the LAN(100) terminal on the Blu-ray Disc player to your Internet source using an Ethernet cable.
  3. Power on the Blu-ray Disc player.
  4. If there is a disc in the Blu-ray Disc player, please remove the disc.
  5. At the xrossmediabar (XMB) , use the arrow keys on the remote control to select "Setup" - "Network Update" and then press the ENTER button.
  6. "Perform version update?" message is displayed.
  7. Select "OK" and then press the ENTER button.
  8. Download process starts and download screen is displayed.
  9. During the download the message "DL */9" ("*" changes from "0" to "9," indicating progress) is displayed on TV screen.
  10. After download process, the upgrade starts and "VUP" appears on the player front panel display.
  11. While the upgrade is installed the message "VUP */9" is displayed on the player front display.
    Note: The "*" changes to "0" through "9," indicating the upgrade progress.
  12. The firmware upgrade is complete when "FINISH" appears on the player front panel display.
    WARNING!! Do not operate or power off the player until this message is displayed. Doing so may cause the Blu-ray Disc player to be unresponsive or to require repair.
  13. The Blu-ray Disc player will automatically power off.
  14. Power on the Blu-ray Disc player
  15. Check the current firmware version to confirm that the upgrade has successfully installed.
    Note: If the last four digits of the version number are 0600, the firmware upgrade was successful.

Possible Issues related to the Network Upgrade

  1. "SYS ERR" or "VUP NG" is displayed on the player front panel display.
    1. Push and hold the "POWER" button for several seconds until the unit power is off.
    2. Turn on the power of the Blu-ray Disc player.
    3. Please execute network upgrade procedure again.
    4. If the symptom does not improve after upgrade again, please contact Sony.

  2. When running network upgrade, the television shows "Connection status cannot be confirmed" and you cannot perform the firmware upgrade.
    There may be a problem with the network connection. Verify that the network connection and settings are correct.
    1. Check the Ethernet cable to make sure it is securely connected to the "LAN(100)" terminal on the player and to the Internet source.
    2. Check the Blu-ray Disc player network settings and confirm that the player has its own IP address.
    Note: If you use a proxy server, enter the IP address of the proxy server you use, instead of the proxy host name, in the "Proxy Server" input field.
    3. Follow the Network Upgrade Instructions again.
  3. The power was shut down during the upgrade process.
    Power on the player again. and then follow the Network Upgrade Instructions again.

  4. The network upgrade process has two parts, first the download and then the upgrade. If, after the download part is finished, the firmware upgrade process is still not finished after running after more than 30 minutes.
    Please contact Sony.

Download the Firmware and Create an Upgrade Disc

If you cannot connect the BDP-S480/S485/S580/S780 to your Internet source, please use the disc upgrade method.
If you successfully updated your BDP-S480/S485/S580/S780 using the "Network upgrade" in the section above, you don't need to apply this procedure.
Important Notes:

  • If you have not done so already, please check the current firmware version to determine if this firmware upgrade is needed for your Blu-ray Disc player.
  • IMPORTANT: At this time, not all versions of CD burning software are able to create an upgrade disc. If you have difficulty creating a disc, please consider using the network upgrade method or requesting a disc. You may also opt to check back later to see if a newer version of the firmware upgrade has become available.
  • WARNING!! Please follow the upgrade instructions carefully. Failure to follow the instructions may interrupt the upgrade process and may cause the Blu-ray Disc player to be unresponsive or to require repair.
  • WARNING!! Do not power off the Blu-ray Disc player or disconnect it from the AC power outlet. Loss of power during the installation of the firmware upgrade may cause the Blu-ray Disc player to be unresponsive or to require repair.
  • Use a brand new CD-R disc to burn the firmware upgrade. The player may not be able to correctly read a dirty disc or a disc with scratches.
    Note: A CD-R disc is strongly recommended. Do not use a CD-RW disc.
  • Recommended operating system for the computer that will download the firmware upgrade:
    Windows® 7, Windows® Vista or Windows® XP is recommended.
  • A drive with CD disc burning capability, and a new blank CD-R disc are required to create the upgrade disc.
  • After you create the disc, please see the Disc Upgrade Instructions section below, for more information.
  • In order to perform the firmware upgrade, it is necessary to have the player correctly connected to a compatible television.
  • It is highly recommended that you print out these instructions for use as a reference during the installation process.

File Info

File Name

  • UPDATA_M07R0600.zip

File Version

  • M07.R.0600

File Size

  • 71.03MB

Release Date

  • 2012-04-13

System Requirements

  • Windows 7
  • Windows Vista
  • Windows XP

Install

Details

Download and Disc Creation Instructions

  1. Download the UPDATA_M07R0600.zip to a temporary or download directory (please note this directory for reference).
  2. Go to the directory where the file was downloaded and verify that the size of the UPDATA_M07R0600.zip file is 75,651,075 bytes.
    a. Right-click the UPDATA_M07R0600.zip file, and click "Properties".
    b. On the "UPDATA_M07R0600.zip Properties" screen, verify that the "Size:" listed is "71.03 MB (75,651,075 bytes)".
    Note: The "Size on disk:" listed may be different. That is normal.
    c. If the file size is different than the "75,651,075 bytes", please download the UPDATA_M07R0600.zip file again.
  3. Double-click the UPDATA_M07R0600.zip file. Then, extract the ZIP file.
  4. The extracted files will be named "MSB07-FW.BIN” and “MSB07-FW.ID”
  5. To create a firmware upgrade disc, write the decompressed files (2 files) to root of CD-R disc using CD-R writing software. Follow the operating instructions for the writing software to create the disc.
    Note: Click here to learn how to create a firmware upgrade CD. 

CD Burning Notes: 

  • IMPORTANT: At this time, not all versions of CD burning software are able to create an upgrade disc. If you have difficulty creating a disc, please consider requesting a disc.
  • The upgrade disc must be finalized. Be sure to select "Finalize CD (No further writing possible)" in your CD burning software to finalize the upgrade disc.
  • If write errors occur during the CD burning process, discard the disc and create a new upgrade disc.
  • Burning the disc using packet writing software is not supported.
    Do not use an upgrade disc created using any other process than the one described above.

Disc Upgrade Instructions

The instructions below are for how to install the firmware upgrade using a disc.

Firmware Upgrade Instructions
WARNING!! Do not power off the player or disconnect it from the AC power outlet. Doing so may damage the player to the point of requiring repair.
WARNING!! Do not press any buttons, except as instructed, until the upgrade is complete. Doing so may damage the player to the point of requiring repair.
Note: The firmware upgrade process takes a minimum of 30 minutes.

  1. Power on the television and make sure it is tuned to the inputs to which the Blu-ray Disc player is connected.
  2. Power on the Blu-ray Disc player.
  3. Place the upgrade disc in the player, and close the disc tray.
  4. After the disc is loaded, the message, "Perform version update?" is displayed on the television.
  5. Use the remote control to select "OK", and then press the ENTER button.
  6. The upgrade process starts and "VUP" appears on the player front panel display.
  7. While the upgrade is installed the message "VUP */9" is displayed on the player front display.
    Note: The "*" changes to "0" through "9," indicating the upgrade progress.
  8. The firmware upgrade is complete when "FINISH" appears on the player front panel display.
    WARNING!! Do not operate or power off the player until this message is displayed. Doing so may result in your player being unresponsive and requiring repair.
  9. Remove the upgrade disc from the player.
  10. Power on the Blu-ray Disc player.
  11. Check the current firmware version to confirm that the upgrade has successfully installed.
    Note: If the last four digits of the version number are 0600, the firmware upgrade was successful.

If The Upgrade Disc Does Not Eject
If the upgrade disc does not eject even though "FINISH" is displayed, please follow the steps below.

  1. Power off the Blu-ray Disc player, and disconnect the AC power cord.
  2. Reconnect the AC power cord while simultaneously holding down the "Open/Close" button on the player.
    Note: Pressing the "Open/Close" button on the remote control does not work. It is necessary to press "Open/Close" button on the Blu-ray Disc player.
  3. Keep pressing the "Open/Close" button until the disc tray opens.
  4. Remove the disc.

Disc Firmware Upgrade FAQ

  1. "SYS ERR" or "VUP NG" is displayed on the player front panel display.
    Please perform the following procedure:
    1. Push and hold the "POWER" button on the player for several seconds until the player powers off.
    2. Power on the Blu-ray Disc player.
    3. Follow the Disc Upgrade Instructions again.
    If the issue persists after performing the upgrade again, please contact Sony.
  2. "VUP" is not displayed on the player front panel display when the upgrade disc is inserted.
    Remove the upgrade disc from the player and delete the upgrade files from your computer.
    Follow the steps in the Download the Firmware and Create an Upgrade Disc section to create a new upgrade disc and then follow the steps in the Disc Upgrade Instructions section to install the firmware upgrade.
  3. The power was shut down during the upgrade process.
    Power on the Blu-ray Disc player, and then follow the Disc Upgrade Instructions again.
  4. When I double click on the UPDATA_M07R0600.zip upgrade file I downloaded from the upgrade web site, the "MSB07-FW.BIN” and “MSB07-FW.ID” files are not created.
    The download may have failed. Delete the downloaded file and follow the steps in the Download the Firmware and Create an Upgrade Disc section to create a new upgrade disc.
  5. The firmware upgrade process is still not finished after running for more than 30 minutes.
    Please contact Sony.